Both a TH350 and a TH400 use a 13 bolt oil pan, so counting bolts will not separate them. The fastest test is the pan shape: the TH350 pan is nearly square with one corner clipped off, while the TH400 pan is a long irregular outline with a bulge on one side. Confirm with the modulator position, then with the output shaft spline count.
Quick Answer: Four Checks
- Pan shape. Five sided and nearly square is a TH350. Long and irregular with an elephant ear bulge is a TH400. Both have 13 bolts.
- Modulator. At the rear of the case is a TH350. On the side of the case is a TH400.
- Kickdown. A cable running to the carburettor is a TH350. An electric kickdown switch and a plug on the case is a TH400.
- Output spline. 27 spline is a TH350. 32 spline is a TH400.
TH350 vs TH400 at a Glance
| Feature | TH350 | TH400 |
|---|---|---|
| Pan bolts | 13 | 13 |
| Pan shape | Nearly square, one clipped corner | Long irregular outline with a side bulge |
| Vacuum modulator | Rear of the case | Side of the case |
| Kickdown | Mechanical cable to the carburettor | Electric switch and solenoid |
| Output shaft spline | 27 | 32 |
| Case and bellhousing | One piece aluminium, about 21.75 in | Larger and heavier, separate bellhousing on most |
| First gear | 2.52:1 | 2.48:1 |
| Introduced | 1969 | 1964 |
| Power to drive it | About 35 hp | About 50 hp |

The Pan Shape Test
Drop under the car and look at the outline of the pan rather than the bolt heads. A TH350 pan is five sided: a square with the rear passenger corner cut on a diagonal. A TH400 pan is much longer than it is wide, with an irregular edge that most people describe as an elephant ear.
This matters because the bolt count is identical. Anyone who tells you a TH350 has a different bolt count from a TH400 has not counted one. The pan shape and the gasket shape are what separate them.
Where Is the Modulator
The vacuum modulator is a small canister with a vacuum hose attached. On a TH350 it sits at the rear of the case. On a TH400 it sits on the side of the case, further forward.
If the hose is missing or split, the transmission will shift late and hard. Before you diagnose anything else, check that the hose is connected and not cracked, because a $5 hose imitates a failing transmission.
Kickdown: Cable or Electric
A TH350 uses a cable from the carburettor or throttle body down to the case. A TH400 uses an electric kickdown switch with a single wire to a solenoid inside the pan.
If the cable is present and connected, you have a TH350 and the cable adjustment controls shift quality. Our guide to the TH350 kickdown cable adjustment covers the setting procedure. There is nothing to adjust on a TH400 in the same way, because the kickdown is a switch rather than a cable.
Tailshaft and Output Spline
Pull the driveshaft and count the splines on the yoke. A TH350 uses a 27 spline output, the same count as a Powerglide and a 700R4. A TH400 uses a 32 spline output, the same as a 4L80E.
This is the check that stops you buying the wrong transmission. The two yokes are not interchangeable and neither are the driveshafts.
Length and Tail Housing
Both transmissions were built with several tail housing lengths, so overall length alone will not identify one. A TH350 case is about 21.75 inches before the tail housing. A TH400 is longer and considerably heavier throughout.
Measure the space you have before you buy anything. If you are replacing one with the other, expect the driveshaft to need shortening or lengthening and the crossmember to move.
Tag, Stamp and Casting Numbers
A TH350 carries a stamped partial VIN on a pad around the bellhousing, plus a broadcast code in some years. A TH400 carries a metal identification plate on the passenger side vertical face of the case, usually stamped with a two digit year, an application letter and a Julian date.
Those formats are covered in more detail in our Borg-Warner and GM identification number guide, and the transmission section collects the rest of the family.
Ratios and What They Mean
| Gear | TH350 | TH400 |
|---|---|---|
| First | 2.52:1 | 2.48:1 |
| Second | 1.52:1 | 1.48:1 |
| Third | 1.00:1 | 1.00:1 |
| Reverse | 1.93:1 | 2.07:1 |
The ratios are close enough that the choice is about strength rather than gearing. The TH400 takes more power to drive, but it survives torque that destroys a TH350. The later electronic descendants follow the same logic, which is why the 4L60E and 4L80E split along the same lines.
Frequently Asked Questions
How can I tell a TH350 from a TH400?
Look at the pan shape first. A TH350 pan is nearly square with one clipped corner, a TH400 pan is long and irregular. Then check the modulator position and count the output shaft splines, 27 for a TH350 and 32 for a TH400.
Do a TH350 and TH400 have the same pan bolt count?
Yes, both use a 13 bolt pan. The bolt count alone cannot identify either transmission, so use the pan outline instead.
Which is stronger, a TH350 or a TH400?
The TH400. It was built for big block engines and heavy vehicles, uses a larger 32 spline output and heavier internals, and it handles far more torque in stock form.
Is a TH350 or TH400 better for a street car?
For a mild small block in a light car the TH350 is lighter and takes less power to drive. For a big block, a heavy car or anything with real torque, the TH400 is the safer choice.
How much power does a TH400 use compared with a TH350?
Roughly 50 hp to drive the TH400 against about 35 hp for a TH350. That difference is one reason people keep the TH350 behind a stock engine.
What does the modulator do?
It reads engine vacuum and adjusts shift pressure and timing. A split or disconnected vacuum hose makes either transmission shift late and firmly, which is easily mistaken for a worn unit.



